Electrical System

Australian Electrical System

The standard voltage for electrical appliances in Australia is 240 volts and 50Hz, basically the same as in the UK.

The electric plugs are different in that they have 3 flat, but angled pins so you may initially need adaptor’s, or arrange to “very quickly” change the plugs when you arrive.

Bring a few power boards, 4 or 6 socket, and just change the one plug to an Australian one, or use one plug adapter, to get you by until you get settled.

6-way-uk-power-board

Electricity supply in the UK

Normal Household Electricity is: 240 volts, 50 Hz, 13 amps max.

The normal electricity system frequency in the UK is 50Hz.
The National Grid has statutory obligations to maintain the frequency within +/- 0.5Hz around this level.  www.nationalgrid.com/uk

In the UK, the average voltage supplied from the national grid is 242V. PDF doc – Click here for link

Electricity supply in Australia

Normal Household Electricity is: 240 volts, 50 Hz, 10 amps max.

The normal mains voltage in Australia is 240 volts, but this can vary between 216 and 254 volts depending on time and load conditions in the distribution system.

The normal maximum current capacity is 10 Amps, but 15 and 20 Amp plug and socket combinations are available, when used with appropriately rated sub-circuits.

The operating frequency is 50 Hertz  www.acma.gov.au

It is very common for new migrants to bring a few British 4 or 6 gang extensions, and change the single plugs on those, to an Australian one, to start of with.

Australian Plugs do NOT have fuses, but are limited to a 10 Amp supply.

Australian Electrical Socket << A standard 10 Amp Electric Household Socket.

And a UK one for comparison >> www.lamps-lights-electrical.co.uk

Are you allowed to rewire an Australian electrical appliance plug yourself ?

I think the answer will depend on where in Australia you live. However almost all plugs purchased will state, on the packaging, that you have to get an Authorised Electrician to fit them,

Australian Capital Territory

No data yet

New South Wales

WorkCover NSW publication 323 states the following in regard to the replacement of plugs and sockets:
Replacement of plugs and sockets:
Plugs and extension cord sockets may be replaced by a non-electrically trained person provided that the person has been trained and found competent to fit the plugs and sockets according to the manufacturer’s instructions.

PDF File at:www.mbansw.asn.au/…/Sept_Dec_07.pdf

Northern Territory

No data yet

Queensland

Electrical work around the home.

Only a licensed electrician or electrical contractor can do electrical work in your home in Queensland.

You may purchase but cannot install electrical accessories (e.g. junction boxes, light switches, plugs, power points, light fittings without a cord) or fixed wire electrical appliances (ceiling fans, some light fittings, stoves, ovens, split system air conditioning).

Source: www.deir.qld.gov.au/…/index.htm

Electrical Dictionary source:
www.deir.qld.gov.au/…/index.htm

competent person” means a person who has acquired, through training, qualifications, experience or a combination of these, the knowledge and skill enabling the person to inspect and test electrical equipment.

fixed electrical equipment” means electrical equipment that is a permanent part of the workplace, such as poles, switchboards, wiring, power points, and other equipment that cannot be unplugged.

Please note an item of electrical equipment connected to electricity by a plug and socket outlet is not permanently electrically connected.

South Australia

No data yet

Tasmania

No data yet

Victoria

No data yet

Western Australia

This information, at www.commerce.wa.gov.au does say: “Although it is legal to connect your own plugs to flexible cords, a faulty connection can kill.”

0 0 votes
Article Rating
Subscribe
Notify of

This site uses Akismet to reduce spam. Learn how your comment data is processed.

0 Comments
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x